MTU Services LLC

WA Contractor# MTUSESL793NP

ID Contractor# RCE-68579

MTU Services LLC logo

Helical Piers in Spokane & North Idaho

Helical piers are steel shafts with screw-shaped plates that we turn into the ground beneath a settling foundation until they reach a measured torque, then bracket to the footing to hold the home in place or lift it back toward level. MTU Services installs helical piers for homes and commercial buildings across Eastern Washington and North Idaho from our shop in Spokane Valley.

What is a helical pier?

A helical pier (also called a helical pile or screw pile) is a galvanized steel shaft with one or more round, spiral plates welded near the tip. Instead of being hammered or pushed into the ground, it is screwed in with a hydraulic drive head, the same way a wood screw pulls itself into a board. The plates bear on firm soil deep below the surface, so the weight of the house moves off the shallow, shifting soil under the footing and onto ground that does not change with the seasons.

Because the installer reads the torque on every pier as it goes in, the crew knows when a pier has reached soil strong enough to carry the load. That reading is recorded for each pier, which gives you a written record of how your foundation was supported.

Helical piers vs. push piers

Both systems move a foundation’s weight onto deeper, stable soil. The right one depends on how heavy the structure is and what the soil looks like. We often decide after the inspection, and some jobs use both.

Helical piersSteel push piers
How they go inScrewed in with a hydraulic drive headPushed down in sections using the weight of the house
How capacity is confirmedInstallation torque on every pierHydraulic pressure needed to push the pier
Best forLighter structures, additions, porches, decks, slabs, and new constructionHeavier homes with enough weight to push against
Needs the structure’s weight to installNo, so they can go in before a building existsYes
Common uses for usSettled additions, garages, porches, light commercial, new footingsSettled two-story homes and heavy masonry walls

Learn more about our full foundation repair and foundation leveling services, or see how we handle bowing walls with basement wall repair.

How we install helical piers

  1. Inspect and measure. We walk the foundation, take elevation readings, and figure out why it moved before we recommend anything.
  2. Plan the pier layout. We set the number and spacing of piers based on the load and the soil. When a structural engineer or a building permit is required, we work with them before the job starts.
  3. Expose the footing. We dig a small access hole at each pier location, outside or inside the home.
  4. Screw each pier to torque. The pier is turned into the ground, adding extension sections until it reaches the target torque for the load it has to carry.
  5. Bracket, stabilize, and lift. A steel bracket connects each pier to the footing. We then hold the foundation where it is or carefully lift it back toward level.
  6. Backfill and document. We backfill, clean up, and give you a record of the depth and torque of every pier.

Why helical piers work in Inland Northwest soils

The ground under homes in our area changes a lot over short distances. Around Spokane and Spokane Valley, many neighborhoods sit on gravels and silts left by the Ice Age floods. On the Palouse around Pullman and Moscow, the windblown loess soil runs deep and loses strength when it gets wet. Across North Idaho, from Coeur d’Alene and Post Falls to Sandpoint, homes often sit on glacial till and clay. Add hard winter frost and spring snowmelt, and shallow footings can settle unevenly.

Helical piers get past that changing surface layer to soil that holds steady, and the torque reading tells us when we have reached it instead of guessing.

Signs your foundation may need piers

  • Floors that slope or feel uneven
  • Doors and windows that stick or will not latch
  • Stair-step cracks in brick or block, or cracks that are wider at one end
  • Drywall cracks above doors and windows
  • An addition, porch, or garage pulling away from the main house

What affects the cost of helical piers

Every job is priced after an inspection because the main cost drivers change from house to house:

  • Number of piers: set by the length of footing that has settled and the load it carries.
  • Depth to firm soil: deeper soft soil means more extension sections per pier.
  • Access: tight side yards, hillside lots, and interior work take more time.
  • Stabilize or lift: lifting a foundation back toward level takes more work than holding it in place.
  • Engineering and permits: required on some projects by the city or county.

Why homeowners choose MTU Services

  • Pier Tech certified foundation repair crews
  • Locally based in Spokane Valley, serving Eastern Washington and North Idaho
  • We find the cause of the movement first, then match the repair to it

Helical pier FAQ

How long do helical piers last?

Hot-dip galvanized helical piers are built to support a structure for decades. The galvanized coating protects the steel from corrosion in the damp soils common in North Idaho and the Palouse.

Can helical piers lift my house back to level?

Often, yes. Once the piers are bracketed to the footing, we can lift the foundation in controlled steps. How far it can safely come back depends on how long it has been settled and what the framing and finishes above can tolerate. We tell you what to expect before we start.

Are helical piers better than push piers?

Neither is better in every case. Helical piers suit lighter structures and new construction because they do not need the building’s weight to install. Push piers suit heavier homes. We recommend the one that fits your house and soil.

Do I need an engineer or a permit?

Some cities and counties require a permit, and some projects call for a structural engineer’s plan. We let you know during the inspection and coordinate it when it applies.

Can helical piers be used for decks, additions, and new construction?

Yes. Because they are screwed in rather than pushed against the structure, helical piers can go in before anything is built, which makes them a common choice for new footings, additions, and decks.

Get a helical pier inspection

If your floors are sloping or cracks keep growing, call MTU Services at (509) 818-6131 or request an estimate. We serve Spokane, Spokane Valley, Coeur d’Alene, Post Falls, the Tri-Cities, Yakima, the Palouse, and communities across Eastern Washington and North Idaho.